Clear scope before work
You see the written scope and the price before any work starts.

A gutter that leaks at the seams, sags between hangers or overflows at the corners is not a cosmetic problem — in Houston it is the start of fascia rot, a wet wall and a slab that never dries out. Most gutter repairs come down to a short list of causes: failed seams, pulled hangers, bad pitch, undersized downspouts, or fascia that has gone soft behind the run. We find the cause, fix it, and water-test the result.
You see the written scope and the price before any work starts.
Gutters, fascia and downspouts are treated as part of the roof water system, not an add-on.
We photograph the fascia, hangers and outlets so you can see the problem yourself.
A Houston roofing company at 5507 Lyons Ave — call (936) 873-7200 and talk to the team.
A repair starts with a full run inspection, not a tube of sealant. Here is what a repair visit covers, and what we check before we quote anything.
We walk every run, check the pitch with a level, probe the fascia, and look at the drip edge, outlets and downspouts. The quote covers the cause, not just the symptom.
Failed seams are cleaned, re-sealed and riveted where the metal allows. Sections too far gone are spliced out and replaced rather than patched over.
Runs that hold standing water are re-pitched toward the downspout and re-hung on solid fascia, with hangers reset on 24-inch centers.
Crushed, separated or undersized downspouts are repaired or replaced, and extensions are fitted so water leaves the slab instead of pooling against it.
Soft fascia and a failed drip edge are the usual reason a repair does not hold. We flag both in writing and fix the wood before the gutter goes back up.
Tell us what your gutters are doing — leaking, sagging, overflowing — and we will arrange an inspection and a written scope before any work starts.
Gutter repair in Houston is diagnosis first and sealant second. A leak at a corner can be a failed seam, a bad pitch, a clogged outlet, or fascia that has rotted behind the run — and each one is fixed differently. We start by finding which one it is.
Houston rain finds the weak point fast. A run that looks fine in a drizzle can overflow in a Harvey-intensity burst, and a seam that holds in dry weather can open up once the metal expands in summer heat. That is why we water-test every repair: running water through the system is the only honest check.
The other thing to know is that gutters are part of the roof water system. A repair that ignores the drip edge or the fascia will fail again at the next storm, usually in the same place.
Tell us what you are seeing — drips at a corner, a sagging run, water over the edge in heavy rain. We will ask a few questions and arrange an inspection.
We walk the runs, check pitch and hangers, probe the fascia and drip edge, and test the outlets. You get photos of what we find.
We explain the cause in plain terms and put the repair scope in writing — what gets sealed, re-hung, re-pitched or replaced, and what it will take.
Seams are cleaned, sealed and riveted; sagging runs are re-pitched and re-hung on solid wood; downspouts are repaired, replaced or extended.
We run water through the system and watch every joint for drips, then walk the job with you and clear the debris. If it still leaks, we have not finished.

A run that holds standing water has a pitch problem. We check pitch with a level and re-pitch toward the downspout — roughly a quarter inch per 10 feet.
Failed seams are cleaned back to bare metal, sealed and riveted. Sealant over dirt and old caulk is a patch that fails in the first hot week.
Hangers reset on 24-inch centers, screwed into solid fascia. Soft wood is replaced first — a hanger in rotten wood is a repair that comes back.
Probes the fascia and soffit for hidden rot before we re-hang anything. What looks solid from the ladder is often soft behind the gutter.
Crushed downspouts are re-formed or replaced, and extensions are fitted so water moves 6 to 10 feet from the slab.
Running water through the finished system is the only honest test. Every joint, corner and outlet is watched for drips before we leave.

Usually a failed corner seam or a clogged outlet. We clean the joint back to bare metal, re-seal and rivet it, and check the outlet is clear — then water-test it.
Pulled hangers and soft fascia. We replace the rotten boards, reset hangers on 24-inch centers, and re-pitch the run so water moves instead of sitting.
Undersized downspouts or a run pitched the wrong way. In Kingwood, pine needles pack the outlets first. We add capacity, re-pitch, and clear the outlets.
Scuppers and interior drains are part of the same water system. We check the scupper, the gutter and the downspout as one path, and clear or repair whichever link is failing.
Houston rain does not forgive a weak gutter. About 52 inches a year, much of it in short, intense bursts, means a run that copes in a drizzle can overflow in a single storm — and once water gets behind the gutter, the fascia rots, the soffit stains, and the slab stays wet. The repair has to match the cause, and in Houston the causes are specific: pine-needle and oak-leaf loading in the canopy neighbourhoods, Harvey-intensity rain overwhelming undersized downspouts, and flat-roof scuppers and interior drains backing up on townhomes.
Pine needles and oak leaves pack valleys, outlets and downspouts. A repair here usually starts with clearing the load, then fixing the pitch the debris was hiding.
Low-slope ranches shed water slowly, and gutters here work hardest at the eaves. We check the drip edge closely — a gap there sends water behind the run.
Flat-roof sections drain through scuppers and interior drains into the gutter. A ponding flat roof and an overflowing gutter are often the same problem.
Large, complex rooflines with long runs and many corners. Corners are where seams fail first, and we seal and rivet them rather than caulking over the problem.
A system sized for average rain fails in a burst. When we repair, we check downspout capacity against the roof area, not just the visible leak.
Water dumped at the slab swells Houston’s clay and moves foundations. A downspout extension is a small repair that prevents a large one.
A 1960s ranch in Meyerland had a corner seam that dripped onto the fascia every rain. The fascia behind it was soft and the soffit was stained.
We cleaned the joint to bare metal, re-sealed and riveted it, replaced the soft fascia board, and water-tested the corner. Dry through the next three storms.
Keep it working: Check the corner after the next heavy rain. A sealed joint should stay dry — if it weeps, call us back before the fascia softens again.
A two-story in Cypress had a run sagging between hangers, holding a pond of water that spilled over the edge and soaked the beds below.
We replaced two rotten fascia boards, reset hangers on 24-inch centers, and re-pitched the run toward the downspout. The standing water is gone.
Keep it working: Keep the outlets clear each fall. A clogged outlet is what turns a good pitch into standing water.
Pine needles had packed the outlets on a Kingwood home, and the corners overflowed in every heavy rain, staining the brick and soaking the foundation beds.
We cleared the runs and outlets, added a downspout for capacity, and fitted leaf guards on the worst runs. The corners stopped overflowing.
Keep it working: Clear the guards after the heavy needle drop. Guards cut cleaning down — they do not remove it entirely.
Most of the expensive damage we see in Houston started as a small gutter problem. Here are the ones we run into most and how we stop them.
Seams fail where metal expands in Houston heat and where sealant was laid over dirt. We clean joints back to bare metal, seal and rivet them, and water-test the result.
Hangers pull out of soft fascia, and then the next hanger takes more load until the run peels off. We replace the rotten wood first, then re-hang on solid fascia.
A run that holds water has a pitch problem. We re-pitch toward the downspout so water moves instead of sitting and breeding mosquitoes.
Undersized downspouts and clogged outlets are the usual cause. We check capacity against the roof area, clear the outlets, and add a downspout where the roof needs one.

Gutter repair is diagnosis work. The leak you can see is rarely the whole story — the cause is usually a few feet away, in a seam, a pitch, or a fascia board that has gone soft. We find the cause, show you photos of it, and fix it so the next storm is the test, not the next leak.

Rated 4.9 out of 5 from 46 Google reviews. The excerpts below are from our Google profile — short excerpts only, with the reviewer’s name, rating and the date Google shows.
“I had storm damage on my roof, and after the first insurance adjuster met with another roofing company, the claim was not approved for roof repair. My niece suggested i call Johnathan, and he came out, met with a different adjuster, and helped get the roof replacement approved.”
Google review · Roof repair for storm & wind damage, gutter installation · Read on Google
“From our first call with Thomas Family Roofing, it was clear they were focused on giving us a quality new roof and making the whole roofing process easy to understand. Miguel explained the scope of the roof replacement, the materials and shingle options…”
Google review · Roof repair for storm & wind damage · Read on Google
“We contacted Thomas Family Roofing for an estimate on repairs for our metal roof in Houston. Luis came out, inspected the roof in person, and explained clearly what needed attention, including a few details about flashing and panel areas that other roofers had missed.”
Google review · Attic venting repairs, gutter installation, roof inspection · Read on Google
It depends on the cause. A single failed seam is a small job; a sagging run that needs fascia replaced and re-hanging is a bigger one. We inspect first and put the scope in writing — we do not quote gutter repairs sight unseen, because the visible leak is rarely the whole story.
Most seams can be fixed: cleaned back to bare metal, sealed and riveted. Replacement is the right call when the metal is corroded through, the run has failed in several places, or the fascia behind it is gone. We will tell you honestly which one it is.
Undersized downspouts or clogged outlets. In light rain the system keeps up; in a Houston burst it cannot. We check downspout capacity against the roof area and clear the outlets before recommending anything.
Usually hangers pulling out of soft fascia. Water gets behind the gutter, the wood rots, and the hangers lose their grip. The fix is to replace the soft boards and re-hang on solid wood — screwing new hangers into rotten fascia just repeats the problem.
Yes. Townhome flat roofs drain through scuppers and interior drains into the gutter system, and we check the whole path — scupper, gutter and downspout — because a ponding flat roof and an overflowing gutter are often the same problem.
Call Thomas Family Roofing at (936) 873-7200 and describe what you are seeing — we will tell you honestly whether it needs a visit or can wait for an inspection.
Call (936) 873-7200Call (936) 873-7200 and tell us what you are seeing — a sagging run, water at the slab, or a gutter that overflows every storm. We will arrange an inspection and give you a written scope before any work starts. Or send a service request through the form and we will call you back.